Imagenes de instalación de las versiones estables para Mageia y OpenMandriva.
OpenMandriva: Mageia (Mageia 9) 20/Agosto/2023 - Anuncio, Descargas.
Blogdrake recomienda descargar las imágenes de instalación (iso) vía torrent para evitar corrupción de datos, aprovechar mejor su ancho de banda y mejorar la difusión de las distribuciones.
¿Como configuro una tarjeta atheros ar242x?
resulta que ya intente unos consejos en post parecidos pero aun no ha aparecido alguna mejora a mi problema.
lo que intente fue lo de bajar el dkms-madwifi, el kernel y demas cosas.
en fin los post son los siguientes.
http://blogdrake.net/node/13821
http://blogdrake.net/consulta/como-configuro-tarjeta-atheros-5007
http://blogdrake.net/node/16925
http://blogdrake.net/consulta/no-consigo-conectarme-por-wifi-con-chip-atheros-ar242x-80211
pongo el resultado de dmesg
solo lo ultimo:
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.29.1-desktop586-4mnb ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
i801_smbus 0000:00:1f.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ath_pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ath_pci 0000:01:00.0: setting latency timer to 64
MadWifi: ath_attach: Switching rfkill capability off.
8139too Fast Ethernet driver 0.9.28
8139too 0000:02:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
8139too 0000:02:01.0: setting latency timer to 64
eth0: RealTek RTL8139 at 0xf8050000, 00:1e:ec:9f:e7:73, IRQ 16
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
wifi0 (ath_pci): not using net_device_ops yet
wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, Radio 10.2)
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
ath0 (ath_pci): not using net_device_ops yet
ath_pci: wifi0: Atheros 5424/2424: mem=0x51300000, irq=16
udev: renamed network interface eth0 to eth1
usb 1-1: device not accepting address 2, error -71
hub 1-0:1.0: unable to enumerate USB device on port 1
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/input/input9
input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/input/input10
input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/input/input11
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: New USB device found, idVendor=0bda, idProduct=8187
usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-1: Product: RTL8187_Wireless
usb 4-1: Manufacturer: Manufacturer_Realtek_RTL8187_
usb 4-1: SerialNumber: 00E04C8FA234
usb 4-1: configuration #1 chosen from 1 choice
cfg80211: Calling CRDA to update world regulatory domain
usb 4-5: new high speed USB device using ehci_hcd and address 3
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Non-volatile memory driver v1.3
wmaster0 (rtl8187): not using net_device_ops yet
phy0: Selected rate control algorithm 'minstrel'
wlan0 (rtl8187): not using net_device_ops yet
phy0: hwaddr 00:e0:4c:8f:a2:34, RTL8187vB (default) V1 + rtl8225z2
usbcore: registered new interface driver rtl8187
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
usb 4-5: New USB device found, idVendor=0bda, idProduct=0158
usb 4-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 4-5: Product: USB2.0-CRW
usb 4-5: Manufacturer: Generic
usb 4-5: SerialNumber: 20060413092100000
usb 4-5: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi5 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
loop: module loaded
usb 4-6: new high speed USB device using ehci_hcd and address 4
usb 4-6: New USB device found, idVendor=04f2, idProduct=b057
usb 4-6: New USB device strings: Mfr=2, Product=1, SerialNumber=3
usb 4-6: Product: CNF7041
usb 4-6: Manufacturer: Chicony Electronics Co., Ltd.
usb 4-6: SerialNumber: SN0001
usb 4-6: configuration #1 chosen from 1 choice
Linux video capture interface: v2.00
uvcvideo: Found UVC 1.00 device CNF7041 (04f2:b057)
input: CNF7041 as /devices/pci0000:00/0000:00:1d.7/usb4/4-6/4-6:1.0/input/input12
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
EXT3 FS on sda1, internal journal
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
wlan0: authenticate with AP 00:18:3f:9b:15:71
wlan0: authenticated
wlan0: associate with AP 00:18:3f:9b:15:71
wlan0: RX AssocResp from 00:18:3f:9b:15:71 (capab=0x431 status=0 aid=2)
wlan0: associated
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory domain updated by AP to: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
scsi 5:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
sd 5:0:0:0: [sdb] Attached SCSI removable disk
sd 5:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 4088500k swap on /dev/sda5. Priority:-1 extents:1 across:4088500k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory intersected:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory domain updated by AP to: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory intersected:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory domain updated by AP to: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory intersected:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
wlan0: authenticate with AP 00:18:3f:9b:15:71
wlan0: authenticated
wlan0: associate with AP 00:18:3f:9b:15:71
wlan0: RX AssocResp from 00:18:3f:9b:15:71 (capab=0x431 status=0 aid=2)
de antemano gracias
y los proximos dias me anotare para empaquetar para mageia =)
Usuario
# 108529 dmesg
wlan0: associated
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory domain updated by AP to: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
ip_tables: (C) 2000-2006 Netfilter Core Team
[drm] Initialized drm 1.1.0 20060810
pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:02.0: irq 26 for MSI/MSI-X
[drm] Initialized i915 1.6.0 20080730 on minor 0
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (16231 buckets, 64924 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
ClusterIP Version 0.8 loaded successfully
xt_time: kernel timezone is -0500
netfilter PSD loaded - (c) astaro AG
IFWLOG: register target
ath0: no IPv6 routers present
wlan0: no IPv6 routers present
CPU0 attaching NULL sched-domain.
CPU0 attaching NULL sched-domain.
wlan0: No ProbeResp from current AP 00:18:3f:9b:15:71 - assume out of range
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory intersected:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
wlan0: authenticate with AP 00:18:3f:9b:15:71
wlan0: authenticated
wlan0: associate with AP 00:18:3f:9b:15:71
wlan0: RX AssocResp from 00:18:3f:9b:15:71 (capab=0x431 status=0 aid=2)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory domain updated by AP to: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
wlan0: no IPv6 routers present
UDF-fs: Partition marked readonly; forcing readonly mount
UDF-fs INFO UDF: Mounting volume 'Sistemas Operat', timestamp 2009/11/12 17:32 (1ed4)
ath0: no IPv6 routers present
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory intersected:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: Calling CRDA for country: US
cfg80211: Current regulatory domain updated by AP to: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
ath0: no IPv6 routers present
usb 4-1: usbfs: USBDEVFS_CONTROL failed cmd sane-find-scann rqt 128 rq 6 len 16 ret -75
atkbd.c: Unknown key pressed (translated set 2, code 0x71 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 71 <keycode>' to make it known.
atkbd.c: Unknown key pressed (translated set 2, code 0x71 on isa0060/serio0).
atkbd.c: Use 'setkeycodes 71 <keycode>' to make it known.
eth1: link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
ath0: no IPv6 routers present
[root@localhost ~]#
-----------------------------------------------
solo existen 10 tipos de personas: los que entienden codigo binario y los que no.
BOFH
# 108531 Varias cosas
Algunos consejos:
0.- En vez de pegar un log gigante como es la salida de dmesg, puedes utilizar pastebin (http://pastebin.org/) para no ensuciar el post.
1.- ¿Qué tipo de tarjeta es, usb, pci? recuerda que no somos una base de datos de hardware ni adivinos ;)
2.- ¿Tienes configurados los repositorios oficiales y PLF?
3.- ¿Utilizaste el centro de control para configurar la tarjeta y la conexión? Aquí Mandriva instala los drivers necesarios para que las tarjetas soportadas funcionen.
Jacen
BOFH y miembro del equipo MDKtrans
Linux user #294897
Usuario
# 108564 0.- ok gracias por tu consejo
0.- ok gracias por tu consejo lo utilizare en el proximo post
1.-(ath_pci: wifi0: Atheros 5424/2424: mem=0x51300000) recuerda que aquí dicen que entre mas información aporte mejor y mas rapido sera solucionado el problema, asi que diriamos que tu pregunta esta fuera de lugar debido a que la respuesta ya se encontraba en el post
2.-efectivamente tengo configurados los repositorios oficiales y los plf.
3.-si use el centro de control mandriva en la seccion hardware, bajo unos paquetes pero no lo soluciono.
aparte descargue la ultima version del kernel y baje los paquetes dkms de la misma version del kernel, y no habia solucion, pero despues de reiniciar y entre en la nueva version del kernel ya funcionaba.
gracias a todos por su atencion.
-----------------------------------------------
solo existen 10 tipos de personas: los que entienden codigo binario y los que no.